Close up of the business end of a Pitch Lap. Diagonal facets are being cut into the face.

A pitch lap is used to polish and figure your mirror. It is used with a polishing abrasive such as Cerium Oxide.

Traditionally, the lap is poured on the tool used to grind the mirror. But this means the that tool is no longer available should you need to return to fine grinding due to a scratch or other problem. Since plaster disks are so simple and inexpensive to make, most people today pour their lap on a separate disk.

To make a pitch lap, first Make a Plaster Disk using your partially or fully ground mirror as a mold. Since the plaster can take some time to cure, a good time to make the curved disk is when you finish with #220 grit. So follow the link to the plaster disk page, and then return here to make your pitch lap.

Making a Pitch Lap

Overview: Using a plaster disk molded on your ground mirror, you will pour heated pitch to form a layer 1/4 to 1/2 inch thick. As it cools, you press it against your mirror so the pitch conforms to the mirror's curve. You will then press or cut channels into the pitch, press again, and trim the excess pitch off the edges.

Materials & Equipment:

• Plaster Disk:  Alternative: Tile or Glass Tool you used for grinding this mirror.
• Pitch: You need about 0.5 kg or 16 oz for a 6" or 8" lap. Use Gugolz 64 or Tempered Burgundy for working at room temperature. See our Grit, Polish & Pitch page for more information.
• Pitch Pot*: Something to melt the pitch in and pour it from. Many people use coffee cans, or buy a very inexpensive pot at a yard sale. A double boiler arrangement works well, and prevents overheating the pitch; you can stand a coffee can on a metal ring made from a cat food can in a pot of water.
• Hot Plate or Electric Stove: To melt the pitch.
• Mixing Spoon or Stick*: To stir the pitch, smooth it when poured and pop any bubbles.
• Liquid Cerium Oxide: Used as a release agent, so the mirror will not stick to the pitch when pressing.
• 2" Wide Masking Tape: Used to make a dam around the plaster disk.
• Razor Blade or Utility Knife: Used to trim the lap, and clean up the channels.
• Channeling Tool: Used to press channels into the soft pitch. 3/8" Wood Dowel, 1/2 Aluminum Angle or Thick Metal Bar will all work.
• Level Work Surface in a room-temperature work environment. Cover it with newspaper or a drop cloth.

*Items that are suggested to be disposable, single use items, or items that will be dedicated to this job.

Procedure:

1. Clean: Make sure your plaster disk is clean and dry. If you are using a glass substrate or tile tool, clean the surface with turpentine.

2. Build a Dam: Using 2" wide masking tape, build a dam at least 3/4" high around the edge of the disk to hold the pitch in when you pour it. Leave a tab at the end by to facilitate later removal.
3. Load Pitch: Load pitch into your pitch pot. The easiest way to remove pitch from its container is to shatter it into little bits with a hammer.
The photo shows shattered pitch, large and small chunks,  in the pitch pot before melting.
4. Warm Mirror: Place your mirror in warm water or under a heat lamp or a warm oven to warm it up. You don't want the warm pitch to be rapidly cooled by a cold mirror when pressing.  A plate glass mirror could shatter from thermal shock when it is pressed into hot pitch (Pyrex mirrors, like Pyrex cookware, handle thermal shock without problems).
5. Melt Pitch: Melt the pitch slowly on low heat - don't let it boil. You want to keep the volatiles in it, so it won't get too hard. Stir occasionally. Heat it just enough to be able to pour it. See Cautions and Warnings above!
6. Pour the pitch onto the tool. Pour to a depth of about 1/2" (this will press down to be thinner when done).
7. Stir & Mound: Stir the pitch slowly to remove trapped air bubbles and allow it to cool uniformly. Try to make a small mound at center (so that when you press, the air will be forced outward from the center). Be patient, let it cool slowly, and continue on only when the mound is firm enough to not flow quickly away.
Work quickly on these next steps,  you must not let the pitch cool down before you are done.
8. Remove the Dam: Using short, sharp tugs, pull the masking tape dam off the tool. If you pull slowly, the pitch will be stretch out like taffy.
9. Coat your warm mirror with a thick layer of Cerium Oxide, so the mirror will not stick to the pitch.
10.  Press the mirror onto the pitch, flattening out the mound and pushing any air bubbles out the sides. Wiggle the mirror and press some more, until all the pitch is in contact with all the mirror, and the pitch is uniformly about 3/8" thick.
11. Channel: Press you channeling tool into the pitch, making squares about 1 to 1.5 inches square. Do not center the squares or channels - a little randomness is good.
Using an aluminum angle to make "Vee" channels.
12. Press again, to get the squares in good contact. Rotate the mirror, take a few short stokes, press, rotate, stroke, press.  Don't press the lap too thin, or close up all the channels. Look through the back of the mirror, and make sure all the squares are in good contact with the glass.
Relax now, you can let things cool down, you are almost done.
13. Trim the Edge: Trim the excess from the edges with a knife or razor. If the pitch has cooled, it will be quite brittle, and with the mirror on top you can just knock it off with a knife. Then, remove the mirror, and bevel the lap edge inwards at a 45° angle. The lap should always be slightly smaller than the mirror, so that when you press, the lap will not grow a "turned up edge".
14. Trim the Channels: Open the channels back up if necessary with a knife or razor blade. This is messy work - many people like to do this underwater to contain the pitch particles.
15. Facet: Use your razor blade or knife to make little facets in the face of each square.  An alternative to making facets with a razor blade is to "Micro-Facet" by pressing a plastic mesh bag, such as is used to for onions or potatoes, between the lap and mirror when hot or warn pressing.
Most of the pictures above are from a single 6" lap; however there are few from an 8" we did the same day, and the last photo is of a totally different lap.

Congratulations - you now have a Pitch Lap to polish and figure your mirror with!

Page last edited 2007-Sep-23